Starting Windows 98... 正在启动Windows 98……
Windows 98 is now starting your MS-DOS-based program Windows 98正在启动基于MS-DOS的程序
Windows 98 is now restarting... Windows 98正在重新启动
Press Esc now to cancel MS-DOS mode and restart Windows 98... 按Esc退出MS-DOS 模式，重新启动Windows 98…
There is an unrecognized command in your CONFIG.SYS file 在你的CONFIG.SYS文件中有不可识别的命令
The following command in your CONFIG.SYS file is incorrect: 在你的CONFIG.SYS有下列错误命令
The sector size specified in this file is too large: 该文件中指定的扇区太大
The following file is missing or corrupted: WIN.COM COMMAND.COM 下列文件丢失或被破坏：WIN.COM和COMMAND.COM
There is an invalid country code or code page in your CONFIG.SYS file 在你的CONFIG.SYS里有一个无效的国家代码
There is an error in the COUNTRY command in your CONFIG.SYS file 在你的CONFIG.SYS里有一个错误的设置国家命令
There is not enough memory for the COUNTRY.SYS file 没有足够的内存来加载COUNTRY.SYS文件
Remove some drivers from your CONFIG.SYS file, and then try again 请从CONFIG.SYS文件中删除部分驱动程序，然后再试
Remove some drivers, and then try again 去除一些驱动程序，然后再试 。这里的驱动程序是指在CONFIG.SYS中使用device或devicehigh命令加载的程序文件
Remove some disk drivers from your CONFIG.SYS file, and then try again 从你的(CONFIG.SYS)移去部分程序，然后再试
The configuration specified in your CONFIG.SYS file is too large for memory 调整你的CONFIG.SYS文件以获得足够大的内存
You have too many block devices specified in your CONFIG.SYS file 调整你的CONFIG.SYS文件以获得block devices
The STACKS setting(s) in your CONFIG.SYS file are incorrect 在你的CONFIG.SYS中堆栈设置不正确
Default stack settings will be used instead 缺省的堆栈设置将被替代使用
There is an error in your CONFIG.SYS file on line XX 在你的CONFIG.SYS里XX行错误
Warning: Logical drives past Z exist and will be ignored 警告：逻辑驱动器Z已经存在，将被忽略
Type the name of the Command Interpreter (e.g., C:/WINDOWS/COMMAND.COM) Press any key to continue… 请输入命令解释器的文件名(如：C:/WIN DOWS/COMMAND.COM)后，按任意键继续
Windows is bypassing your startup files
Minimal network support will be loaded if available Windows正在跳过你的启动文件 。如果网络可用，最小网络支持将被加载
Windows is starting the command prompt only Windows正在启动命令字符模式
Windows will prompt you to confirm each startup command Windows将提示你确认每一个启动命令
The compression driver cannot be set up correctly 压缩驱动程序不能被正确加载
Get a version from your vendor that is compatible with this version of Windows 从你的供应商那里获得一个与Windows版本相兼容的版本
Process the system registry 运行系统注册表
Create a startup log file (BOOTLOG.TXT) 创建启动日志BOOTLOG.TXT文件
Process your startup device drivers (CONFIG.SYS) 运行CONFIG.SYS文件中的设备驱动
Process your startup command file (AUTOEXEC.BAT) 运行AUTOEXEC.BAT中的启动命令
Load the Windows graphical user interface 装入WINDOWS图形用户界面(GDI)
Warning: Windows has detected a registry/configuration error. Choose, Command prompt only, and run SCANREG 警告：Windows检测到一个注册表或配置错误选择DOS操作模式，运行SCANREG
Warning: Windows has detected a compressed drive access error. Choose Safe mode command prompt only, to help you identify the problem 警告：Windows检测到一个访问压缩驱动器错误，选择安全模式下的MS-DOS，来帮助你识别这个问题
Warning: Windows did not finish loading on the previous attempt. Choose Safe mode, to start Windows with a minimal set of drivers 警告：Windows在刚才尝试后不能够完成加载，选择安全模式，用最小驱动启动你的电脑
推荐阅读
- 电脑一直充电有影响吗
- 电脑qq录屏会自动保存吗
- 笔记本电脑播放无声音
- 企业微信有电脑版的吗
- 电脑页面截图快捷键是什么
- 电脑登录微信手机为什么不提示
- 电脑全屏下面的任务栏还在
- hewlett packard是什么电脑
- 荞麦冷面做法
- 电脑卡的原因