CISCO路由器产品配置手册二--PSDN( 二 )


aaa authorization exec tacacs
aaa authorization network tacacs
aaa accounting exec start-stop tacacs
aaa accounting network start-stop tacacs
enable secret 5 $1$kN4g$CvS4d2.rJzWntCnn/0hvE0
!
interface Ethernet0
ip address 10.111.4.20 255.255.255.0
!
interface Serial0
no ip address
shutdown
interface Serial1
no ip address
shutdown
!
interface Group-Async1
ip unnumbered Ethernet0
encapsulation ppp
async mode interactive
peer default ip address pool Cisco2511-Group-142
no cdp enable
group-range 1 16
!
ip local pool Cisco2511-Group-142 10.111.4.21 10.111.4.36
tacacs-server host 10.111.4.2
tacacs-server key tac
!
line con 0
exec-timeout 0 0
password cisco
login authentication no_tacacs
line 1 16
login authentication tacacs
modem InOut
modem autoconfigure type usr_courier
autocommand ppp
transport input all
stopbits 1
rxspeed 115200
txspeed 115200
flowcontrol hardware
line aux 0
transport input all
line vty 0 4
password cisco
!
end
2. DDR(dial-on-demand routing)实例
此例通过Cisco 2500系列路由器的aux端口实现异步拨号DDR连接 。Router1拨号连接到Router2 。其中采用PPP/CHAP做安全认证,在Router1中应建立一个用户,以对端路由器主机名作为用户名,即用户名应为Router2 。同时在Router2中应建立一个用户,以对端路由器主机名作为用户名,即用户名应为Router1 。所建的这两用户的password必须相同 。
相关命令如下:
任务 命令
设置路由器与modem的接口指令 chat-script script-name EXPECT SEND EXPECT SEND (etc.)
设置端口在挂断前的等待时间 dialer idle-timeout seconds
设置协议地址与电话号码的映射 dialer map protocol next-hop-address [name hostname] [broadcast] [modem-scriptmodem-regexp] [system-script system-regexp] [dial-string]
设置电话号码 dialer string dial-string
指定在特定线路下路由器默认 使用的chat-script script {dialerreset} script-name
Router1:
hostname Router1
!
enable secret 5 $1$QKI7$wXjpFqC74vDAyKBUMallw/
!
username Router2 password cisco
chat-script cisco-default "" "AT" TIMEOUT 30 OK "ATDT T" TIMEOUT 30 CONNECT c
!
interface Ethernet0
ip address 10.0.0.1 255.255.255.0
!
interface Async1
ip address 192.200.10.1 255.255.255.0
encapsulation ppp
async default routing
async mode dedicated
dialer in-band
dialer idle-timeout 60
dialer map ip 192.200.10.2 name Router2 modem-script cisco-default 573
dialer-group 1
ppp authentication chap
!
ip route 10.0.1.0 255.255.255.0 192.200.10.2
dialer-list 1 protocol ip permit
!
line con 0
line aux 0
modem InOut
modem autoconfigure discovery
flowcontrol hardware
Router2:
hostname Router2
!
enable secret 5 $1$F6EV$5U8puzNt2/o9g.t56PXHo.
!
username Router1 password cisco
!
interface Ethernet0
ip address 10.0.1.1 255.255.255.0
!
interface Async1
ip address 192.200.10.2 255.255.255.0
encapsulation ppp
async default routing
async mode dedicated
dialer in-band
dialer idle-timeout 60
dialer map ip 192.200.10.1 name Router1
dialer-group 1
ppp authentication chap
!
ip route 10.0.0.0 255.255.255.0 192.200.10.1
dialer-list 1 protocol ip permit
!
line con 0
line aux 0
modem InOut
modem autoconfigure discovery
flowcontrol hardware
!

推荐阅读