专用Cisco路由器的替代品Zebra( 五 )



清单 14. Failover 之前路由器 A 的路由表
RouterA#show ip routeCodes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGPD - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter areaN1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGPi - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area* - candidate default, U - per-user static route, o - ODRP - periodic downloaded static routeGateway of last resort is not set10.0.0.0/24 is subnetted, 3 subnetsR10.0.2.0 [120/1] via 192.168.2.1, 00:00:11, FastEthernet0/0C10.0.0.0 is directly connected, Loopback0R10.0.1.0 [120/1] via 192.168.0.2, 00:00:18, Serial0/0192.168.0.0/30 is subnetted, 1 subnetsC192.168.0.0 is directly connected, Serial0/0192.168.1.0/30 is subnetted, 1 subnetsR192.168.1.0 [120/1] via 192.168.0.2, 00:00:18, Serial0/0[120/1] via 192.168.2.1, 00:00:11, FastEthernet0/0192.168.2.0/30 is subnetted, 1 subnetsC192.168.2.0 is directly connected, FastEthernet0/0failover 之后:
清单 15. Failover 之后路由器 A 的路由表
RouterA#show ip routeCodes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGPD - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter areaN1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGPi - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area* - candidate default, U - per-user static route, o - ODRP - periodic downloaded static routeGateway of last resort is not set10.0.0.0/24 is subnetted, 3 subnetsR10.0.2.0 [120/2] via 192.168.0.2, 00:00:09, Serial0/0C10.0.0.0 is directly connected, Loopback0R10.0.1.0 [120/1] via 192.168.0.2, 00:00:09, Serial0/0192.168.0.0/30 is subnetted, 1 subnetsC192.168.0.0 is directly connected, Serial0/0192.168.1.0/30 is subnetted, 1 subnetsR192.168.1.0 [120/1] via 192.168.0.2, 00:00:09, Serial0/0192.168.2.0/30 is subnetted, 1 subnetsR192.168.2.0 [120/2] via 192.168.0.2, 00:00:10, Serial0/0使用 Zebra 配置 OSPF 路由
完成 RIP 的配置后,我们开始配置 OSPF 路由 。尽管 OSPF 和 RIP 可以同时使用,不过为了配置的简化,我们现在只使用 OSPF 。我们只需要把 ripd 服务停掉,就可以在 Zebra 中将 RIP 禁用 。
# service ripd stop
和前面一样,我们从 OSPF 的一个基本的配置文件开始,这次是 ospfd.conf,文件所在目录仍是 /etc/zebra 。
QQRead.com 推出数据恢复指南教程 数据恢复指南教程数据恢复故障解析常用数据恢复方案硬盘数据恢复教程数据保护方法数据恢复软件专业数据恢复服务指南清单 16. 一个基本的 /etc/zebra/ospfd.conf 文件
hostname speedmetal-ospfpassword zebraenable password zebra
然后,我们启动 OSPF 服务:
# service ospfd start
对 OSPF 的配置比 RIP 简单:基本上我们仅仅需要告诉 OSPF 去广播所有它知道的路由 。
配置 OSPF 的端口是 2604 。
下面是我们配置 OSPF 的会话 。

清单 17. OSPF 配置会话
[root@speedmetal zebra]# telnet 127.0.0.1 2604User Access VerificationPassword: zebraspeedmetal-ospf> enablePassword: zebraspeedmetal-ospf# configure terminalspeedmetal-ospf(config)# router ospfspeedmetal-ospf(config-router)# network 0.0.0.0/0 area 0speedmetal-ospf(config-router)# endspeedmetal-ospf# writeConfiguration saved to /etc/zebra/ospfd.confspeedmetal-ospf# show run Current configuration:!hostname speedmetal-ospfpassword zebraenable password zebra!!router ospf network 0.0.0.0/0 area 0!line vty!endspeedmetal-ospf#ospfd.conf 配置文件的修改结果如下:
清单 18. Zebra 修改后的 /etc/zebra/ospfd.conf 文件
!! Zebra configuration saved from vty!2003/08/19 14:22:17!hostname speedmetal-ospfpassword zebraenable password zebra!!!interface lo!interface eth0!interface eth1!interface dummy0!router ospf network 0.0.0.0/0 area 0!line vty!在 Cisco 路由器上配置 OSPF

推荐阅读