云南龙网

  1. 首页 > 云知道 > >

FreeBSD的启动信息参考

云知道

FreeBSD 在 i386?上启动，如果启动正常，您将看到在屏幕上有很多信息滚动，最后您会看到登陆命令行 。您可以通过键入 Scroll-Lock和使用 PgUp 与 PgDn来查看信息，再键入 Scroll-Lock 回到命令行 。记录信息可能不会显示（缓冲区的限制） 。您可以通过键入 dmesg 来查看 。使用您在安装过程中设置的用户名/密码来登陆 。（例子中使用 rpratt） 。除非必须的时候请不要用 root 用户登陆 。典型的启动信息：（忽略版本信息）
【FreeBSD的启动信息参考】Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
Timecounter "i8254"　frequency 1193182 Hz
CPU: AMD-K6(tm) 3D processor (300.68-MHz 586-class CPU)
　Origin = "AuthenticAMD"　Id = 0x580　Stepping = 0
　Features=0x8001bf
　AMD Features=0x80000800
real memory　= 268435456 (262144K bytes)
config> di sn0
config> di lnc0
config> di le0
config> di IE0
config> di fe0
config> di cs0
config> di bt0
config> di aic0
config> di aha0
config> di adv0
config> q
avail memory = 256311296 (250304K bytes)
Preloaded elf kernel "kernel" at 0xc0491000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc049109c.
md0: Malloc disk
Using $PIR table, 4 entries at 0xc00fde60
npx0:
on motherboard
npx0: INT 16 interface
pcib0:
on motherboard
pci0:
on pcib0
pcib1:
at device 1.0 on pci0
pci1:
on pcib1
pci1:
at 0.0 irq 11
isab0:
at device 7.0 on pci0
isa0:
on isab0
atapci0:
port 0xe000-0xe00f at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0:
port 0xe400-0xe41f irq 10 at device 7.2 on pci0
usb0:
on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
chip1:
at device 7.3 on pci0
ed0:
port 0xe800-0xe81f irq 9 at
device 10.0 on pci0
ed0: address 52:54:05:de:73:1b, type NE2000 (16 bit)
isa0: too many dependant configs (8)
isa0: unexpected small tag 14
fdc0:
at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0:
at port 0x60-0x64 on isa0
atkbd0:
flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0:
irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
vga0:
at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0:
at flags 0x1 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0:
at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/15 bytes threshold
ppbus0: IEEE1284 device found /NIBBLE
Probing for PnP devices on ppbus0:
plip0:
on ppbus0
lpt0:
on ppbus0
lpt0: Interrupt-driven port
ppi0:
on ppbus0
ad0: 8063MB
[16383/16/63] at ata0-master using UDMA33
ad2: 8063MB
[16383/16/63] at ata1-master using UDMA33
acd0: CDROM
at ata0-slave using PIO4
Mounting root from ufs:/dev/ad0s1a
swapon: adding /dev/ad0s1b as swap device
Automatic boot in progress...
/dev/ad0s1a: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/ad0s1a: clean, 48752 free (552 frags, 6025 blocks, 0.9% fragmentation)
/dev/ad0s1f: FILESYSTEM CLEAN; SKIPPING CHECKS

推荐阅读


上一篇：低温施药要点

下一篇：劝人奋发向上的名言