7.MM Series
8.MM HitTablet
相信大家都知道自己的滑鼠该选那一种的吧??如果你的滑鼠是可以2键与3键切换的
建议你使用3键的!!因为Xwindow下会使用到第三个键! 另外logitech的滑鼠一般都
应该要选第六项!
选好之後接著会根据你选的mouse问一些东西!你可以看他的说明来决定要选Yes或
No! 根据我的经验如果你不知道要选Yes或No的时候, 多半以选No为佳!尤其如果
你是选第六种mouse的, 当它问你要不要使用ChordMiddle时, 请千万要选No.不然
使用的时候会有问题! 当你在使用Xwindow时如果mouse不听话的话, 你可以再做
一次mouse的设定!
接下来它会问你你的mouse的device档是那一个, 用预设的/dev/mouse就可以了!
当你的滑鼠不听话的时候, 你可以先确定一下/dev/mouse是否link到正确的档案!
(4)设定keyboard:
在设定完mouse後, 它会问你关於keyboard的设定:
Please answer the following question with either "y" or "n".
Do you want to enable these bindings for the Alt keys?
直接按Enter跳过就行了!
(5)设定萤幕:
开始进入重要的部份了. 你一开始会看到下面的选项:
It is VERY IMPORTANT that you do not specify a monitor type with a
horizontal
sync range that is beyond the capabilities of your monitor. If in doubt,
choose a conservative setting.
hsync in kHz; monitor type with characteristic modes
131.5; Standard VGA, 640x480 @ 60 Hz
231.5 - 35.1; Super VGA, 800x600 @ 56 Hz
331.5, 35.5; 8514 Compatible, 1024x768 @ 87 Hz interlaced (no 800x600)
431.5, 35.15, 35.5; Super VGA, 1024x768 @ 87 Hz interlaced, 800x600 @ 56
Hz
531.5 - 37.9; Extended Super VGA, 800x600 @ 60 Hz, 640x480 @ 72 Hz
631.5 - 48.5; Non-Interlaced SVGA, 1024x768 @ 60 Hz, 800x600 @ 72 Hz
731.5 - 57.0; High Frequency SVGA, 1024x768 @ 70 Hz
831.5 - 64.3; Monitor that can do 1280x1024 @ 60 Hz
931.5 - 79.0; Monitor that can do 1280x1024 @ 74 Hz
10Enter your own horizontal sync range
Enter your choice (1-10):
此时请拿起你先前准备的资料比对上面的选项, 如果有一样的数据的就选那一项,
如果找不到的话, 就请按输入"10", 输入自己萤幕的水平扫描频率!
接下来就是设定垂直扫描频率了:
You must indicate the vertical sync range of your monitor. You can either
select one of the predefined ranges below that correspond to industry-
standard monitor types, or give a specific range. For interlaced modes,
the number that counts is the high one (e.g. 87 Hz rather than 43 Hz).
150-70
250-90
350-100
440-150
5Enter your own vertical sync range
同样的, 如果有相同的就输入该选项的代码. 若没有的话,就选5然後输入自己
的参数. 特别要提醒的是, 如果设定完之後, 执行Xwindow萤幕却乱掉了. 不妨
重新设定你的垂直扫描频, 从1,2,3的选项中挑一个range比你小却最接近你的选项.
然後它会问你要一些厂牌, 或是萤幕的型号的资料料, 随便输入就可以了!
(6)设定显示卡:
接下来就是最重的重头戏了! 首先它会问你要不要看看内建的一些card的资料!
要不要随便你! 反正最後还是要做相同的设定的!在这里我们就选不要了!
再下来它会问你你的显示卡是哪一类的:
1The XF86_Mono server. This a monochrome server that should work on any
推荐阅读
- 为啥会觉得自己的照片很丑
- ESQL编程使用说明
- packages/ports 使用说明
- 54 FreeBSD连载:配置文件XF86Config
- 47 FreeBSD连载:使用xf86config配置X服务器
- 高温干旱谨防葡萄缩果病
- 通义千问邀请码怎么弄 通义千问邀请码获得方法及使用说明
- 打药时常犯的三种错误
- 路由器Telnet使用说明
- 少时常与鲍叔牙游,鲍叔知其贤翻译 少时常与鲍叔牙游,鲍叔知其贤什么意思